광섬유 설치에서의 마이크로덕트 피팅: 역할, 종류 및 선택
오울루의 네트워크 설치 기사가 광케이블 포설 작업 전에 두 개의 마이크로덕트 구간을 연결할 때, 그녀는 공칭 덕트 라벨을 보고 커넥터를 선택한 뒤 컴프레서를 가동했다. 압력이 안정되지 않았고 케이블은 몇 분 만에 멈춰 섰다. 피팅이 애초에 불량품이었던 것은 아니었다: 해당 경로는 덕트 외경이 제각각이었고 절단면도 제대로 다듬어지지 않았던 것이다. 팀이 치수를 확인하자,…
업계 인사이트
뉴스 및 블로그
마이크로덕트, 광케이블 설치 및 공압 연결 전문가를 위한 업계 뉴스, 기술 가이드 및 실무 프로젝트 인사이트.
최신 기사
기사
상세보기
건설용 강철 커넥터: B2B 조달 가이드
When a project buyer in Oulu encountered mismatched steel connector packs during a warehouse release, the crew trial-fitted the first brackets and found that the hole pattern would not align with the approved steelwork. The visible failure looked like a supplier mix-up; the review showed that incomplete drawings, ambiguous coating language, and no incoming-inspection plan had allowed the wrong requirement to be purchased. Quick…
공압 스트레이트 피팅: 자동화 시스템의 효율성 향상
When a maintenance engineer in Oulu replaced a leaking elbow on a packaging line, the cylinder still hesitated. The leak had gone, but the branch still had a small-bore connector, a long tube run, and unnecessary direction changes. Replacing parts alone was not the answer; specifying the flow path was. Quick answer: Pneumatic straight fittings can preserve available pressure by joining aligned tube runs…
공압 스트레이트 피팅: 신뢰할 수 있는 에어 라인을 위한 올바른 디자인 선택하기
When a maintenance engineer in Oulu replaced a straight connector on a packaging line, the new part appeared to seat correctly; within minutes, a faint hiss became a pressure drop that slowed a pneumatic cylinder. The visible failure looked like a bad fitting, but the reversal came when the team measured the tube outside diameter, checked the thread seal, and found that a nominally…
원터치 피팅: 작동 원리 및 선택 방법
A push-in fitting can appear correctly assembled while leaking because the tube was cut at an angle, the outside diameter was wrong or the port thread did not match. The collet and elastomer seal work only when the tube, fitting, thread and service conditions are specified as one connection. One-touch fittings use a collet to retain tubing and an O-ring or similar seal to…
엔드 스톱 커넥터: 선택 및 설치 가이드
An end stop is a closure decision, not simply a small cap at the end of a duct. The route may be vacant, awaiting cable, isolated for a pressure check or retained as a spare. Each condition changes the required retention, sealing evidence, access and reuse plan. Choose an end stop connector by measured duct OD, closure duty and test method. NEN EN 50411-2-8…
인터넷 커넥터와 플러그: 네트워크 프로젝트를 위한 실용 가이드
"Internet connector" can mean an 8P8C modular plug, a fiber connector or even a microduct fitting in a search result. The correct choice depends on the transmission medium and the complete channel. A familiar RJ45 label does not identify cable category, conductor construction, shielding or termination compatibility. Separate copper Ethernet, fiber and duct decisions before ordering. An internet connector must match the cable and…
광주 무역박람회(캔톤 페어) 개최 전 중국의 에어 호스 피팅 제조업체를 평가하는 방법
At a trade fair, a polished catalogue and a low quotation do not prove that an air-fitting supplier can hold a thread, seal or material specification through production. Due diligence is a sequence: define the interface, review traceability, inspect a sample, agree tests and control changes before treating a factory as production-ready. Evaluate a China supplier with a written drawing, sample and acceptance plan.…
산업용 성능을 위한 상위 5가지 에어 호스 피팅: 선택 가이드
The best air hose fitting depends on the connection that must be made, not a universal ranking. A quick coupler for frequent tool changes has different evidence requirements from a push-in tube fitting, threaded elbow or barbed hose end. A mechanically similar part can still leak, restrict flow or separate if the tube, thread, medium and pressure are wrong. Compare air hose fittings by…