光ファイバー配線におけるマイクロダクト継手：役割、種類、および選定
オウルのネットワーク設置作業員が、光ファイバーの布設作業の前に2つのマイクロダクト区間を接続した際、彼女は公称ダクトのラベルを見てコネクタを選び、コンプレッサーを始動させた。しかし圧力は安定せず、ケーブルは数分以内に停止してしまった。継手が最初から不良品だったわけではなく、配管ルート上に異なる外径のダクトが混在していたことと、切断面の処理が不適切だったことが原因であった。チームが寸法を確認すると、…
業界インサイト
ニュース＆ブログ
マイクロダクト、ファイバー敷設、空圧接続のプロフェッショナルに向けた業界ニュース、技術ガイド、実践的なプロジェクトインサイト.
最新の記事
記事
詳細を見る
建設用鋼製コネクタ：B2B調達ガイド
When a project buyer in Oulu encountered mismatched steel connector packs during a warehouse release, the crew trial-fitted the first brackets and found that the hole pattern would not align with the approved steelwork. The visible failure looked like a supplier mix-up; the review showed that incomplete drawings, ambiguous coating language, and no incoming-inspection plan had allowed the wrong requirement to be purchased. Quick…
空気圧用ストレート継手：オートメーションシステムの効率化
When a maintenance engineer in Oulu replaced a leaking elbow on a packaging line, the cylinder still hesitated. The leak had gone, but the branch still had a small-bore connector, a long tube run, and unnecessary direction changes. Replacing parts alone was not the answer; specifying the flow path was. Quick answer: Pneumatic straight fittings can preserve available pressure by joining aligned tube runs…
空気圧用ストレート継手：信頼性の高いエアラインに適したデザインの選び方
When a maintenance engineer in Oulu replaced a straight connector on a packaging line, the new part appeared to seat correctly; within minutes, a faint hiss became a pressure drop that slowed a pneumatic cylinder. The visible failure looked like a bad fitting, but the reversal came when the team measured the tube outside diameter, checked the thread seal, and found that a nominally…
ワンタッチ継手：その仕組みと選定方法
A push-in fitting can appear correctly assembled while leaking because the tube was cut at an angle, the outside diameter was wrong or the port thread did not match. The collet and elastomer seal work only when the tube, fitting, thread and service conditions are specified as one connection. One-touch fittings use a collet to retain tubing and an O-ring or similar seal to…
エンドストップコネクタ：選定と取り付けガイド
An end stop is a closure decision, not simply a small cap at the end of a duct. The route may be vacant, awaiting cable, isolated for a pressure check or retained as a spare. Each condition changes the required retention, sealing evidence, access and reuse plan. Choose an end stop connector by measured duct OD, closure duty and test method. NEN EN 50411-2-8…
インターネット用コネクタとプラグ：ネットワークプロジェクトの実践ガイド
"Internet connector" can mean an 8P8C modular plug, a fiber connector or even a microduct fitting in a search result. The correct choice depends on the transmission medium and the complete channel. A familiar RJ45 label does not identify cable category, conductor construction, shielding or termination compatibility. Separate copper Ethernet, fiber and duct decisions before ordering. An internet connector must match the cable and…
広州交易会（カントンフェア）の前に中国のエアーホース継手メーカーを評価する方法
At a trade fair, a polished catalogue and a low quotation do not prove that an air-fitting supplier can hold a thread, seal or material specification through production. Due diligence is a sequence: define the interface, review traceability, inspect a sample, agree tests and control changes before treating a factory as production-ready. Evaluate a China supplier with a written drawing, sample and acceptance plan.…
産業用パフォーマンスのためのエアホース継手トップ5：選定ガイド
The best air hose fitting depends on the connection that must be made, not a universal ranking. A quick coupler for frequent tool changes has different evidence requirements from a push-in tube fitting, threaded elbow or barbed hose end. A mechanically similar part can still leak, restrict flow or separate if the tube, thread, medium and pressure are wrong. Compare air hose fittings by…