2-way 14/10 mm direct-buried HDPE microduct tube bundle
This 2-way DB HDPE tube bundle is presented for FTTH and underground fiber cable blowing routes.
The source states 14 mm sub-duct OD, 10 mm ID, 1.2 mm wall or sheath, a 30.4 mm x 16.4 mm bundle profile and at least 1,350 N inner tensile strength. The table also states 25 bar pressurization and supplier test values; confirm the current drawing and batch evidence.
TECHNICAL DETAILS
Published product facts
Physical and Mechanical Properties – Inner Micro duct 14/10mm
The outer and inner diameter shall show, under visual examination without damage and no reduction of diameter greater than 15%.
IEC 60794-1-2
Method E3
3
Kink
≤140mm
-
IEC 60794-1-2
Method E10
4
Impact
Striking surface radius: 10mm
Impact Energy: 1J
Number of impact: 3 times
Recovery time: 1 hour
Under visual examination, there shall be no damage to the micro duct.
IEC 60794-1-2
Method E4
5
Bend radius
Number of turns: 5
Mandrel diameter: 168mm
Mumber of cycles: 3
The outer and inner diameter shall show, under visual examination without damage and no reduction of diameter greater than 15%.
IEC 60794-1-2
Method E11
6
Friction
/
≤0.1
FCST
Pos.
Item
Specification
1
Appearance
Smooth outer wall (UV-stabilized) without visible impurities; well-proportioned color, no bubbles or cracks; with defined markings
on outer wall.
2
Tensile strength
Use Pull socks to tension a sample in accordance with table below:
Sample length: 1m
Tensile speed: 20mm/min
Load: 2200N
Duration of the tension: 5 min.
No visual damage or residual deformation greater than 15% of the duct assembly outer diameter.
3
Crush Resistance
A 250mm sample after 1 minute load time and 1 hour recovery time. Load (plate) shall be 2000N. The imprint of the plate on the
sheath is not considered as mechanical damage.
No visual damage or residual deformation greater than 15% of the duct assembly outer diameter.
4
Impact
Striking surface radius shall be 10mm and impact energy 3J. Recovery time shall be one out. The imprint of the striking surface on
the microduct is not considered as mechanical damage.
No visual damage or residual deformation greater than 15% of the duct assembly outer diameter.
5
Bend
Diameter of mandrel shall be 40X OD of sample, 4 turns, 3 cycles.
No visual damage or residual deformation greater than 15% of the duct assembly outer diameter.
PRODUCT DETAIL IMAGES
Product Detail
The original product detail images are retained for visual reference. Confirm the quoted model, dimensions and test requirements before ordering.
SELECTION GUIDE
Selecting a 2-way 14/10 mm microduct bundle
Use these checkpoints to prepare a product-specific enquiry and close the fit, test and documentation questions before ordering.
Confirm the two pathwaysMatch two 14/10 mm ducts to the cable and spare requirement.
Check clearanceConfirm the 10 mm ID and 8.5 mm blowing-ball clearance stated in the table.
Plan the routeUse the 30.4 mm x 16.4 mm profile and confirmed bend limits.
Oulu Automatic Equipment presents itself as a supplier of microduct connectors, HDPE microduct systems, cable blowing accessories and pneumatic fittings for telecom contractors, distributors and OEM partners.
The supplier’s Service page describes support from product consultation and customized solutions through production, delivery and after-sales. Include these details in a product enquiry:
Match two 14/10 mm ducts to the cable and spare requirement.
Target quantity, model or size mix, sample needs and packing preference.
Drawings, route conditions, pressure or sealing tests and compliance documents.
Current MOQ, price, freight, sample timing and production timing to be confirmed in the quotation.
Company-level support and commercial terms should be reconfirmed for the selected product and order.
Share dimensions, route conditions and quantities for a product-specific quotation.Send product requirements
PROJECT SUPPORT
Plan the right microduct solution
Review the microduct route solutions and Service pages for project context, then confirm exact fit, documents and commercial terms in the quotation.
Zhejiang Oulu Automatic Equipment Co., Ltd. Short Description: Model Number:4ways DB Tube Bundle Type:Micro Duct & Tube Bundle Place of Origin:Wenzhou, China Brand Name:ANMASPC Aging-resistant, anti corrosion of chemicals. HDPE Tube Bundle is convenient in construction, save time...
Zhejiang Oulu Automatic Equipment Co., Ltd. Short Description: Essential details Model Number:19ways 7/3.5mm DB Tube Bundle Type:Micro Duct & Tube Bundle Place of Origin:Wenzhou, China Brand Name:ANMASPC Use:FTTH Warranty Time:12months Network:None Sub duct Inner diameter:3.5mm Sub duct outer diameter:7mm PE...
Zhejiang Oulu Automatic Equipment Co., Ltd. Short Description: The micro-pipeline system consists of single-hole microtubes, microtubule bundle tubes(abbreviated as bundle tube),high-performance air-blown optical cables,pipeline system accessories and air-blown construction machine and tools. - A bundle of micro- or mini-tubes (strengthened...
